Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Grade 10 chromium steel balls
Dynaplug tubeless tire repair plugs are constructed from viscoelastic rubber impregnated cord. The plugs are specially designed to be inserted directly into a puncture after object has been removed. - Combo pack includes x5 replacement plugs: x3 pointed brass soft nose tip plugs x2 Megaplugs - Made in USA - The Megaplugs are compatible with: Megapill tool, Megaplugger tool, and the Racer series of tools - The brass soft nose tip are compatible with all Dynaplug tools, except for Air Road tool NOTE: for Air Road plugs, please use part # 380-2020
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
Stainless spoke nipple flat washers from Whisky. - .3mm Thickness
The Rear Wheel Cover is a critical safety component for carrying passengers on the Globe Haul ST. The easy-to-install guards cover openings on the frame and rear rack to prevent fingers, toes, and clothes from getting too close to the moving wheel and chain. They also protect from dust and grease to keep riders and bikes cleaner. **For Globe Haul ST bike customers: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Compatible with Haul ST. - Includes two upper fender covers and two lower wheel covers. - Easy toolless installation.
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Dynaplug tubeless tire repair plugs are constructed from viscoelastic rubber impregnated cord and non-abrasive brass tip. The plugs are specially designed to be inserted directly into a puncture after object has been removed. - Pack of 5 replacement plugs with pointed brass soft nose tip - Compatible with all Dynaplug repair tools, except for Air Road tool - Made in USA
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
These MTH 716 Conversion Caps allow your SRAM MTH 716 front hub to accept a 15 x 100mm thru-axle.
Page 1 of 1